Heater pic's

[GREENHOUSE]

Tony sorry for the delay hear is what I have for pic's. If I get time I will take some more pic's later today of the finish look

Mike

[Naumoff]

Thanks Mike.
I have a couple of pics. I have the demisters aswell, made it a little more fun. Hard piped it to the firewall and I am waiting on some black AN fittings.
It will be piped in the engine compartment with SS line and AN fittings.

That little heater does move some air. Two speed motor and I was able to wire a Lucas switch for it. Real clean looking. The PVC tees worked out well.
Also need some more 2" heater duct hose.The demisters are hooked up just need some more hose to pipe back to the passenger side.

[Naumoff]

Got my back ordered fittings from Summit and finished my heater install last week. Backorder was for black fittings


Hoses fit nice from firewall to water pump and manifold

http://images.snapfish.com/34655%3B4%3B2%7Ffp33%3A%3Enu%3D3255%3E%3B%3A2%3E94 4%3EWSNRCG%3D323358%3B7%3B6%3A3%3Bnu0mrj

Made a bracket for coated clamps that attaches to valvecover bolt

http://images.snapfish.com/34655%3B4%3B2%7Ffp344%3Enu%3D3255%3E%3B%3A2%3E944% 3EWSNRCG%3D323358%3B7%3B85%3A6nu0mrj

http://images.snapfish.com/34655%3B4%3B2%7Ffp342%3Enu%3D3255%3E%3B%3A2%3E944% 3EWSNRCG%3D323358%3B7%3B6%3A45nu0mrj

http://images.snapfish.com/34655%3B4%3B2%7Ffp346%3Enu%3D3255%3E%3B%3A2%3E944% 3EWSNRCG%3D323358%3B7%3B6%3A37nu0mrj

[Naumoff]

Had to modify one of the fittings to match the factory one that goes in the top of the manifold.
The little heater works great and puts out plenty of heat.

Had to drill out inside of fitting to fit a 1/2" O.D. tube which I JB welded into place
http://images.snapfish.com/34655%3B4%3B2%7Ffp339%3Enu%3D3255%3E%3B%3A2%3E944% 3EWSNRCG%3D323358%3B7%3B6%3A38nu0mrj

http://images.snapfish.com/34655%3B4%3B2%7Ffp33%3B%3Enu%3D3255%3E%3B%3A2%3E94 4%3EWSNRCG%3D323358%3B7%3B8597nu0mrj

http://images.snapfish.com/34655%3B4%3B2%7Ffp342%3Enu%3D3255%3E%3B%3A2%3E944% 3EWSNRCG%3D323358%3B7%3B85%3A3nu0mrj

[GREENHOUSE]

Is the black hose you have there cloth braid or steel braided. I need to replace the steel braided line I have to my carberator and go with the black for a better look. Are the black anodized fittings any better than the red and blue fittings as far as scratching? How long of a backorder was it ?
Thanks
Mike

[Naumoff]

Mike the hoses I have are braided stainless that have been painted.
They do make a black braided hose which I would have bought but I already purchased the hoses and fittings from Unique for my oil cooler and just modified them a little. painted look is good for now.
The black fittings seem to be better against scratching as far as I can tell.
I went with black just for the look.