View Full Version : One step at a time
pgermond
November 29th, 2003, 01:09 PM
Probably doesn't look like much progress has been made to the novice, but it's getting a lot closer to being ready to haul the mail......... [:P]
http://www.uniquecobra.com/uploaded/pgermond/5 one step at a time.JPG
Phil
427 Roadster, #4279436
Southern Automotive FE
Toploader
Roseville (N.Cal)
GeorgiaSnake
November 29th, 2003, 10:10 PM
Phil I noticed you took the three bolts out of the trunk hinge, it's much better to leave them in and remove the bolt at the hinge attachment point. Same thing for the hood. It can be a real pain to get the alignment right.
The car looks great, keep it up.
Randy
Unique 289 FIA
Southern Automotive 396
Team III 16's
Brilliant Silver
GeorgiaSnake
November 29th, 2003, 10:10 PM
Phil I noticed you took the three bolts out of the trunk hinge, it's much better to leave them in and remove the bolt at the hinge attachment point. Same thing for the hood. It can be a real pain to get the alignment right.
The car looks great, keep it up.
Randy
Unique 289 FIA
Southern Automotive 396
Team III 16's
Brilliant Silver
dmiller
November 29th, 2003, 10:11 PM
i made that same mistake, probably be wishing i didn't later.
doug
dmiller
November 29th, 2003, 10:11 PM
i made that same mistake, probably be wishing i didn't later.
doug
pgermond
November 29th, 2003, 11:34 PM
Actually, the painter did me that favor. Live-n-learn :)
Phil
427 Roadster, #4279436
Southern Automotive FE
Toploader
Roseville (N.Cal)
pgermond
November 29th, 2003, 11:34 PM
Actually, the painter did me that favor. Live-n-learn :)
Phil
427 Roadster, #4279436
Southern Automotive FE
Toploader
Roseville (N.Cal)
glenn
November 29th, 2003, 11:54 PM
phil,
your car looks great, can't wait till i get mind back from the painters.have you had any problems with connecting fuel lines to fuel pump and to the tank? anyway hope to be at your stage of the build in a few weeks.
Glenn
glenn e. snider
glenn
November 29th, 2003, 11:54 PM
phil,
your car looks great, can't wait till i get mind back from the painters.have you had any problems with connecting fuel lines to fuel pump and to the tank? anyway hope to be at your stage of the build in a few weeks.
Glenn
glenn e. snider
pgermond
November 30th, 2003, 09:27 AM
Glenn, I didn't have any problem with the fuel lines. Today I bent, ran, and connected all the hydraulic lines (brakes front-n-rear, and clutch). Kind of a pain :( but I got it done. I used a heat reflective shield/sleeve where any line came close to the header - - which was all of them. Good luck, and keep us posted.
Phil
427 Roadster, #4279436
Southern Automotive FE
Toploader
Roseville (N.Cal)
pgermond
November 30th, 2003, 09:27 AM
Glenn, I didn't have any problem with the fuel lines. Today I bent, ran, and connected all the hydraulic lines (brakes front-n-rear, and clutch). Kind of a pain :( but I got it done. I used a heat reflective shield/sleeve where any line came close to the header - - which was all of them. Good luck, and keep us posted.
Phil
427 Roadster, #4279436
Southern Automotive FE
Toploader
Roseville (N.Cal)
Brent
November 30th, 2003, 07:53 PM
Looks great!!!
You have been putting in some long hours too.
Brent
Brent
November 30th, 2003, 07:53 PM
Looks great!!!
You have been putting in some long hours too.
Brent
Powered by vBulletin® Version 4.2.5 Copyright © 2024 vBulletin Solutions Inc. All rights reserved.